Install Android 2.3.5 Gingerbread on HP TouchPad Tablet – How to Guide
Android 2.3.5 Gingerbread on HP TouchPad Installation via TouchDroid Project ( How to ) – Now you can Download and Flash/Install Android 2.3.5 Gingerbread on HP TouchPad Tablet . How to Flash Android 2.3.5 on HP Tablet with detailed information and if yes then follow this Guide.
Actually, News of the walkthrough comes from Touch-Droid Forums. Where Flashing Android on HP TouchPad Tablet is somewhat risky matter, which requires considerable skill with Computers to follow and there is great potential you might brick your HP TouchPad during this operation.
From Touch-Droid :
ATTENTION NON-DEVS: THIS IS A PRE-ALPHA BUILD, WIFI DOES NOT WORK, WITH ALONG MANY OTHER THINGS, DO NOT INSTALL UNLESS YOU ARE GOING TO BUILD FROM THIS IMAGE.
I have decided to release a system dump from my TouchPad which contains a semi-working build of Android 2.3.5 with working touchscreen on the HP TouchPad. Please use this data and the below steps on installation as you see fit. I hope this release will light a fire under the community to work together on a full working port!
*** I am in no way responsible if this bricks or otherwise damages your TouchPad ***
How to Flash Android 2.3.5 Gingerbraed on HP TouchPad Tablet
Important Note – We are not responsible for any loss of data as a resulkt of the Malfunctioning of your HP TouchPad Tablet.
Step 1 – Download the System.tar.bz and android.uImage from the Torrent Download Link (Direct Link)
Step 2 – First of all setup novaterm, before proceeding furthur and for that you need to visit this WiKi Page and follow the instructions for setting up novaterm on your OS (works on Windows, MAC and Linux).
Be sure to place the two files you downloaded in Step 1 inside the novaterm folder.
Step 3: Connect your HP TouchPad to your PC using a USB cable. (DO NOT MOUNT IT)
Step 4: Open up command prompt/terminal on your PC and type the following:
Step 5: In order to install Android, we must first create partitions for it on the TouchPad’s internal memory. Run the following commands in novaterm:
lvm.static lvresize -L -1706M /dev/store/media
lvm.static lvcreate -L 10M -n android-persist store
lvm.static lvcreate -L 32M -n android-etc store
lvm.static lvcreate -L 320M -n android-system store
lvm.static lvcreate -L 320M -n android-cache store
lvm.static lvcreate -L 1024M -n android-data store
Step 6 – Using Novaterm, the partition must be mounted in tmp/system:
mount -o loop -t ext3 /dev/mapper/store-android–system /tmp/system/
Step 7 – Open up a new command prompt/terminal windows run the following:
novacom put file://tmp/system/system.tar.bz < system.tar.bz
Step 8 – Now from novaterm, unzip the System.tar.gz file that you already Downloaded in Step 1 to /tmp/system:
tar -xvf system.tar.bz
mv * ../
rm -rf system
Step 9: Using novaterm, unmount /tmp/system
Step 10: You are now required to boot into bootie by running the following command in novaterm:
Step 11: Using command prompt/terminal, change to your novaterm folder and run the following:
novacom boot mem:// < android.uImage
By now, Android 2.3.5 Gingerbread will be installed on your HP TouchPad. You now need to boot into it.
Step 12: Keep pressing the Volume UP button on your TouchPad until there is a purple line on the right hand side of the TouchPad’s display.
That’s is it , These are the Steps, you followed correctly, then you will now have a Booted Android 2.3.5 Gingerbread on HP TouchPad Tablet.
Everytime you want to boot into Android, you will need to repeat steps 10 and 11.
Important Note – If you want to get rid of Android 2.3.5 Gingerbread, open up novaterm and run the following commands
lvm.static lvremove store/android-persist
lvm.static lvremove store/android-system
lvm.static lvremove store/android-data
lvm.static lvremove store/android-cache
lvm.static lvremove store/android-etc
lvm.static lvresize -L +1706M /dev/store/media
If you are not understanding this Steps guide, then you can follow these two videos: